Table of Contents

Loading ...

Berofos Integration

Wazo offers the possibility to integrate a berofos failover switch within a HA cluster.

This is useful if you have one or more ISDN lines (i.e. T1/E1 or T0 lines) that you want to use whatever the state of your Wazo HA cluster. To use a berofos within your Wazo HA installation, you need to properly configure both your berofos and your Wazo, then the berofos will automatically switch your ISDN lines from your master node to your slave node if your master goes down, and vice-versa when it comes back up.

You can also use a Berofos failover switch to secure the ISDN provider lines when installing a Wazo in front of an existing PBX. The goal of this configuration is to mitigate the consequences of an outage of the Wazo : with this equipment the ISDN provider links could be switched to the PBX directly if the Wazo goes down.

Wazo does not offer natively the possibility to configure Berofos in this failover mode. The Berofos Integration with PBX section describes a workaround.

Installation and Configuration

Master Configuration

There is nothing to be done on the master node.

Slave Configuration

First, install the bntools package:

apt-get install bntools

This will make the bnfos command available.

You can then connect your berofos to your network and power it on. By default, the berofos will try to get an IP address via DHCP. If it is not able to get such address from a DHCP server, it will take the 192.168.0.2/24 IP address.

emoji-exclamation The DHCP server on Wazo does not offer IP addresses to berofos devices by default.

Next step is to create the /etc/bnfos.conf{.interpreted-text role="file"} file via the following command:

bnfos --scan -x

If no berofos device is detected using this last command, you'll have to explicitly specify the IP address of the berofos via the -h option:

bnfos --scan -x -h <berofos ip>

At this stage, your /etc/bnfos.conf{.interpreted-text role="file"} file should contains something like this:

[fos1]
mac = 00:19:32:00:12:1D
host = 10.34.1.50
#login = <user>:<password>

It is advised to configure your berofos with a static IP address. You first need to put your berofos into flash mode :

  • press and hold the black button next to the power button,
  • power on your berofos,
  • release the black button when the red LEDs of port D start blinking.

Then, you can issue the following command, by first replacing the network configuration with your one:

bnfos --netconf -f fos1 -i 10.34.1.20 -n 255.255.255.0 -g 10.34.1.1 -d 0
emoji-exclamation
  • -i is the IP address
  • -n is the netmask
  • -g is the gateway
  • -d 0 is to disable DHCP

You can then update your berofos firmware to version 1.53:

wget http://www.beronet.com/downloads/berofos/bnfos_v153.bin
bnfos --flash bnfos_v153.bin -f fos1

Once this is done, you'll have to reboot your berofos in operationnal mode (that is in normal mode).

Then you must rewrite the /etc/bnfos.conf (mainly if you changed the IP address):

bnfos --scan -x -h <berofos ip>

Now that your berofos has proper network configuration and an up to date firmware, you might want to set a password on your berofos:

    bnfos --set apwd=<password> -f fos1
    bnfos --set pwd=1 -f fos1

You must then edit the /etc/bnfos.conf{.interpreted-text role="file"} and replace the login line to something like:

login = admin:<password>

Next, configure your berofos for it to work correctly with the Wazo HA:

    bnfos --set wdog=0 -f fos1
    bnfos --set wdogdef=0 -f fos1
    bnfos --set scenario=0 -f fos1
    bnfos --set mode=1 -f fos1
    bnfos --set modedef=1 -f fos1

This, among other things, disable the watchdog. The switching from one relay mode to the other will be done by the Wazo slave node once it detects the master node is down, and vice-versa.

Finally, you can make sure everything works fine by running the xivo-berofos command:

xivo-berofos master

The green LEDs on your berofos should be lighted on ports A and B.

Connection

Two Wazo

Here's how to connect the ISDN lines between your berofos with:

  • two Wazo in high availability

In this configuration you can protect up two 4 ISDN lines. If more than 4 ISDN lines to protect, you must set up a Multiple berofos configuration.

Here's an example with 4 ISDN lines coming from your telephony provider:

ISDN lines (provider)
  | | | |
  | | | |
+---------------------------------------------+
|    A           B           C           D    |
| 1|2|3|4     1|2|3|4     1|2|3|4     1|2|3|4 |
+---------------------------------------------+
              | | | |                 | | | |
              | | | |                 | | | |
            +--------+              +--------+
            | wazo-1 |              | wazo-2 |
            +--------+              +--------+

Two Wazo and one PBX

Here's how to connect your berofos with:

  • two Wazo in high availability,
  • one PBX.

In this configuration you can protect up two 2 ISDN lines. If more than 2 ISDN lines to protect, you must set up a Multiple berofos configuration.

Logical view:

+--------+                            +-----+

-- Provider ----| wazo-1 | -- ISDN Interconnection --| PBX | -- Phones

:

+--------+ +-----+

:   | wazo-2 |

    +--------+

This example shows the case where there are 2 ISDN lines coming from your telephony provider:

ISDN lines (provider)
  | |
  | |
+------------------------------------------------------+
|    A               B            C           D        |
| 1|2|3|4         1|2   3|4      1|2|3|4     1|2   3|4 |
+------------------------------------------------------+
      | |     CPE | |   | | NET          CPE | |   | | NET
      | |   spans | |   | | spans      spans | |   | | spans
      | |       +----------+              +------------+
      | |       |  wazo-1  |              |   wazo-2   |
      | |       +----------+              +------------+
      | |
      | |
    +------+
    | PBX  |
    +------+

One Wazo and one PBX

This case is not currently supported. You'll find a workaround in the Berofos Integration with PBX section.

Multiple berofos

It's possible to use more than 1 berofos with Wazo.

For each supplementary berofos you want to use, you must first configure it properly like you did for the first one. The only difference is that you need to add a berofos declaration to the /etc/bnfos.conf{.interpreted-text role="file"} file instead of creating/overwriting the file. Here's an example of a valid config file for 2 berofos:

[fos1]
mac = 00:19:32:00:12:1D
host = 10.100.0.201
login = admin:foobar

[fos2]
mac = 00:11:22:33:44:55
host = 10.100.0.202
login = admin:barfoo

emoji-warning berofos name must follow the pattern fosX where X is a number starting with 1, then 2, etc. The bnfos tool won't work properly if it's not the case.

Operation

When your Wazo switch the relay mode of your berofos, it logs the event in the /var/log/syslog{.interpreted-text role="file"} file.

Default mode

Note that when the berofos is off, the A and D ports are connected together. This behavior is not customizable.

Uninstallation

It is important to remove the /etc/bnfos.conf file on the slave node when you don't want to use anymore your berofos with your Wazo.

Reset the Berofos

You can reset the berofos configuration :

  1. Power on the berofos,
  2. When red and green LEDs are still lit, press & hold the black button,
  3. Release it when the red LEDs of the D port start blinking fast
  4. Reboot the beronet, it should have lost its configuration.

External links